Digital Electronics Lab BBTK AE-1305BBTK

Digital Electronics Lab BBTK AE-1305BBTK

SPECIFICATIONS

  • Housed in attractive wooden cabinate with cover
  • Breadboard area with more than 1200 TIE points
  • Custom required TIE points are also available
  • In-built power supply
  • Power Supply provided +5V/1Amp, GND

Digital Electronics Lab OPAMP AE-1305OP

Digital Electronics Lab OPAMP AE-1305OP

Specifications

  • Sumer/Subtractor, Differntiator/Integrator, Inverting/Non-inverting Amplifier, Voltage Follower/Current Follower/Clipping Amplifier, All applications using 741 IC
  • On board resistors having range from 10W - 1MW .
  • On board capacitors having range from 1Kpf - 1mf.
  • Diodes 1N 4001 (4 Nos.), Diode 1N4148 (2 Nos.), Zener Diodes 4.7V (2 Nos.).
  • Potentiometer 1K, 10K, 47K, 100K,1M.
  • One socket for 14 pin IC.
  • Power supply :+/-15V DC, GND & 16-0-16V AC.
  • Set of Patch chords & Manual.

Digital Electronics Lab ALTK AE-1305ALTK

Digital Electronics Lab ALTK AE-1305ALTK

Specifications

  • On board resistors having range from 10W - 1MW
  • On board capacitors having range from 1Kpf - 47mf.
  • Onboard Timer IC 555 (2 Nos.), Op-Amp IC 741 (4 Nos.),Voltage regulator IC 723 (1 No.).
  • One no. of Comparator IC 710.
  • Diodes 1N 4001 (4 Nos.), Diode 1N4148 (2 Nos.).
  • 2 Nos. of Zener Diodes (4.7V).
  • Potentionmeter Variable pot for 1K, 10K, 47K, 100K,1M.
  • On board power supply : 16-0-16V AC, +/-12V DC, GND.
  • Set of Patch chords & manual with experiments.

Digital Electronics Lab DL-DIT-IC AE-1305DL

Digital Electronics Lab DL-DIT-IC AE-1305DL

Specifications

  • 9 TTL compatible logic level inputs & 8 LED's for output.
  • Dual Color LED for Logic low & Logic high.
  • Four crystal generated clock output.
  • Single pulse generation, Logic probe.
  • seven segment display with BCD inputs.
  • Gate IC's, Flip Flop Proveded on board with pin connectors.
  • Two blank sockets, 14 pin & 16 pin each for different IC's.
  • In-built power supply.
  • Set of Patch chords & Manual.

Digital Electronics Lab digital ic trainer kit with in-built power supply AE-1287A

Digital Electronics Lab digital ic trainer kit with in-built power supply AE-1287A

  • 9 TTL/CMOS compatible logic level inputs.
  • ON/OFF input switch
  • 8 digital output displayed on 8 IC’s.
  • 1K Pod & 10K pod for variable resistance
  • ON BOARD BASIC GATE IC’s 7400, 7402, 7404, 408, 7432, 74LS76, 74LS86 soldered with input & output available at 2mm socket
  • TTL or CMOS logic selectable by a toggle switch provided on board
  • Logic HIGH and logic LOW are displayed by dual color LED.
  • Four crystal generated clock output of 1MHz, 100Hz, 10Hz, and 1Hz.
  • Facility for single pulse generation by a push button switch.
  • Logic probe to check logic LOW, logic HIGH and pulse.
  • 4 seven segment display with BCD inputs.
  • Facility of segment control on two displays.
  • Experiments for Study of NAND, NOT, NOR, AND, XOR, DECODER, FLIP-FLOP, COUNTER, DEMULTIPLEXER, HALF ADDER, FULL ADDER, HALF SUBTRACTOR, FULL SUBTRACTOR etc.
  • 14 pin & 16 pin socket for any addition digital IC for experiments
  • Addion IC supplied for experiments in blank socket 7420, 7495, 74193, 7483, 7485, 7447, 74121, 74163 & 7490
  • In-Built Power Supply of 5V/1Amp.
  • User’s Manual, Cables & Connectors.

Digital Electronics Lab Analog Digital Trainer Kit with in-built Power Supply AE-1287B

Digital Electronics Lab Analog Digital Trainer Kit with in-built Power Supply AE-1287B

  • TTL or CMOS logic selectable by a toggle switch
  • Logic HIGH and logic LOW are displayed by dual color LED.
  • Four crystal generated clock output of 1MHz, 100Hz, 10Hz, and 1Hz..
  • Facility for single pulse generation by a push button switch.
  • Logic probe to check logic LOW, logic HIGH and pulse.
  • Four 7 segment display with BCD inputs.
  • Facility of segment control on two displays.
  • Bread board area with facility of more than 1200 TIE points.
  • Capable of accepting wire diameters from 0.3 to 0.8mm.
  • It has in-built supply of +3V to 15VDC/300mA, -3V to -15VDC/350mA, 15 - 0 -15VAC/500mA
  • User’s Manual, Cables & Connectors.

Digital Electronics Lab Digital Trainer Kit With in-built Power Supply AE-1287C

Digital Electronics Lab Digital Trainer Kit With in-built Power Supply AE-1287C

  • 8 TTL/CMOS compatible logic level inputs.
  • TTL or CMOS logic selectable by a toggle switch
  • Logic HIGH and logic LOW are displayed by dual color LED.
  • Four crystal generated clock output of 1MHz, 100Hz, 10Hz, and 1Hz.

Facility for single pulse generation by a push button switch.

  • Logic probe to check logic LOW, logic HIGH and pulse.
  • Four seven segment display with BCD inputs.
  • Facility of segment control on two displays.
  • Bread board area with facility of more than 1200 TIE points.
  • Capable of accepting wire diameters from 0.3 to 0.8mm.
  • In-built Power Supply
  • User’s Manual, Cables & Connectors.

Experiments Can Be Performed

Study of NAND, NOT, NOR, AND, XOR, DECODER, FLIP-FLOP, COUNTER, DEMULTIPLEXER, HALF ADDER, FULL ADDER, HALF SUBTRACTOR, FULL SUBTRACTOR, SHIFT REGISTERS etc.

Optional

Set OF ICs To Perform Above Experiments :
(7400, 7402, 7404, 7408, 7432, 7486, 7474, 7476, 74138, 7493, 74139, 7490, 7492)

Communication Lab Phase Shift Key Modulation & Demodulation Abron

Communication Lab Phase Shift Key Modulation & Demodulation Abron

  • Built in +/-5V, +/-12V/350 mA DC Power Supply
  • Built in Carrier Generator: 10 KHz
  • Built in Modulating Signal Generator 1 KHz
  • PSK Modulator
  • PSK Demodulator
  • Assembled in Wooden Box with circuit screen printed on Glass Epoxy PCB with 2mm socket for test points & to see the waveforms
  • Set of Patch Chords & Experimental Manual.

Communication Lab Ask Modulation & Demodulation Trainer Abron

Communication Lab Ask Modulation & Demodulation Trainer Abron

  • +/-12V, +/-5V/350 mA DC Power Supply
  • Carrier Generator: 50 KHz - 100 KHz,5Vp-p
  • Clock Generator : 100Hz - 10KHz
  • Programmable Word Generator : Cyclic8-Bit Word
  • ASK Demodulator Assembled in Wooden Box with circuit screen printed on Glass Epoxy PCB with 2mm socket for test points & to see the waveforms.
  • Set of Patch Chords & Experimental Manual.

Communication Lab Frequency Modulation/Demodulation  Trainer Abron

Communication Lab Frequency Modulation/Demodulation Trainer Abron

Frequency Modulation is accomplished using IC 8038 a function generator IC with built-in VCO. On-board carrier and modulating signal with power supplies are provided. PLL IC 565 is used to demodulate FM signal. Frequency deviation, Modulation Index etc., are studied using this trainer.

Hardware Specification

  • +/-12V/350 mA DC Power Supply
  • Carrier Generator 75 KHz
  • Modulating signal Generator 10 KHz
  • Based on IC CXA1691BS
  • Low current comsumption
  • Volume control
  • Built in speaker
  • Built in audio amplifier
  • Low power dissipation
  • Fault findings given in manual
  • Fault creating by jumpers, so helpul to understand the working of actual receiver
  • Can be used as normal receiver to tune different frequencies
  • Each section like audio amplifier, FM modulator etc. is printed on board with test points.
  • Housed in attractive cabinet
  • In-built power supply
  • Operating temperature - 10 degree C to +60 degree C

Microprocessor Study Modules Trainer Abron

Microprocessor Study Modules Trainer Abron

The Study Modules can be connected to the STD BUS of any 8/16 bit Microprocessor/Microcontroller Training kit offered by Vinytics to perform the experiments in the laboratory. This helps in learning about real time interfacing problems of the Microprocessors/Microcontrollers. All Microprocessor/Microcontroller taining kits offered by Vinytics can be connected to these modules through 50 pin FRC cable.

AE-1305-8212 Memory Decoder Study Card
The Study Card based on 8212 helps to understand the function of decoder.

AE-1305-8251 USART Study Card
This Study card helps to understand the functions of Universal Synchronous/Asynchronous Receiver Transmiter. LED’s are providing for different signals like chip select, Data Bust, Read/Write, etc.

AE-1305-8253 Programmable Timer Study Card
This study card enables the user to understand the operation in all six modes of programmable timer/counter chip (8253) LED’s are provided for different signals like Chip Select, Data Bus, Read/Write etc.

AE-1305-8255 PPI Study Card
This study card helps to understand the working of the Programmable peripherals interface chip in various modes. LED’s are provided for different signals like Read/Write, A1, A1, Data Bus, Chip Select and all ports etc.

AE-1305-8237/8257 DMA Study Card
This study card helps to understand the working of Direct Memory Access chip in different modes. LED’s are provided for different signals like Data Bus, Address Bus (A3-A0), TC, HRQ, AEN, IR, IW, MR, MW, CS etc.

AE-1305-8259 PIC Study Card
This study card helps to understand the working of programmable interrupt controller. LED’s are provided for different signals like Data Bust, Read, Write, INTA, A0, CS etc.

AE-1305-8279 Keyboard Display Controller Study Card
This study card helps to understand the working of keyboard/display controller. LED’s are provided for different like Data Bus, Read, Chip Select, A0, INT etc.

AE-1305-8155 PPI with Timer Study Card
This study card helps to understand the working of programmable peripherals interface chip with time & RAM, LED’s are provided for different signals like Data Bus, Chip Select, Read, Write, A0, A1 and all ports etc.

AE-1305-6264/62256 RAM Study Card
This study card helps to understand the working of Random Access Memory (RAM) 6264. LED’s are provided for different signals like Data Bus, Read, Write, Chip Select etc.

AE-1305-373 Latch Study Card
This study card helps to understand the working of chip used for latching the address. LED’s are provided for Data Bus to enable the user to know which data is present on input/output.

New arrivals in interfacing modules

31/2 Digit ADC Card
This interfacing cards uses ICL 7107 31/2 digit A/D converter with 0-2V input to be displayed on the microprocessors.

Sound/Speaker Card
This interfacing cards uses clock generated from 8253 timer to generate different frequencies on to the speaker.

Printer Interface Card
This interfacing cards uses 8255 of the Microprocessor/Microcontroller to print output on to the printer.

Microprocessor Interfacing Modules

Microprocessor Interfacing Modules

The Interfacing Modules can be connected to the lines of any 8/16 bit Microprocessor/Microcontroller Training kit offered by Vinytics to perform the experiments in the laboratory. This helps in learning about real time interfacing problems of the Microprocessors/microcontroller.
All Microprocessor/Microcontroller training kits offered by Vinytics can be connected to these modules through 26 pin FRC cable.

AE-1305-ADC ADC Interface
This interface consists of 8 bit analog to digital converter uses successive approximation method for conversion, 8 LED’s are provided to display the digital value of analog input.

AE-1305-ADC0809 ADC-0809 Interface
Uses 8 bit ADC-0809 monolithic CMOS device with in-built 8 channel multiplexer. 8 LED’s are provided to display the digital value of the input analog signal (optional). The complete operation of A/D converter chip can be understood using this card.

AE-1305-DAC Daul DAC Interface
Consists of two independent 8 bit digital to analog converter alongwith a stable regulated voltage source using 723 regulator. The current output of DAC are converted to voltage using operational amplifies.

AE-1305-LC Logic Controller Interface
The logic controller interface provides the user 8 TTL buffered outputs & input. The logic state of each input & output is indicated by LED. This module can be effectively used to teach 8255 in input & output modes. It can also simulate ladder networks.

AE-1305-ES Elevator Simulator
This interface simulates the control operation of an elevator. The elevator is considered to function within a building having 4 floors. A key & corresponding LED indicator serves as request button & request status indicator. The LED’s also indicate the position of the elevator within the shaft.

AE-1305-ICT IC Tester Interface
The interface explain the working of IC testers for 14 pin or 16 pin digital IC’s with the help of micro processor. Three personality modules are to be inserted in three different sockets for the IC under test. A socket is provided for inserting the IC to be tested.

AE-1305-DI Display Interface
A Four digit display using shift registers can be obtained on this module. This module has the capability to display in any combination. The display can be from right to left or left to right. A delay can be put between two display.

AE-1305-SMC Stepper Motor Controller Interface
This module can control Stepper Motor in three parameters such as direction, speed & number of steps. It has got driver transistors for driving all the phases of the motor. The interface is useful for robotics & control applications.

AE-1305-SM Stepper Motors

Torque
Kg.-cm
Max. Speed
RPM
Steps
Degree
Volts/
Amps
0.25
100
7.5
5V/250mA
3
50
1.8
5V/1.5A
6
40
1.8
12V/3A
10
25
1.8
12V/4.5A

AE-1305-KB Keyboard Interface
A Calculator style keyboard consisting of the keys 0 to 9, *, +, -, /, C, CE and two user definable keys, allowing the user to study a number of techniques used in keyboard interface like software deboucing, two key lock out and keyboard encoding & pausing.

AE-1305-LCD LCD Display Interface
A 16x1 Liquid Crystal Display using shift registers can be obtained on this module. This module has the capability to display in any combination. The display can be from right to left or left to right. A delay can be put between two display.

AE-1305-TLC Traffic Light Controller Card
The Traffic Light Controller Card has RED, YELLOW & GREEN LED’s to demonstrate the use of Microprocessor in controlling the traffic movement under the control of program. It is a good example of use of Microprocessor in common applications.

AE-1305-Temp Temperature Measurement Card
Sensor to measure temperature upto 100oc, alongwith room temperature compensation and amplifier with output of 0-5V corresponding to the temperature.

AE-1305-DC DC Motor Controller Card
The AE-1305-DC card can control the speed of DC motor alongwith its direction under the control of the software programme.

AE-1305-ROC Relay & Opto Copuler Card
The AE-1305-ROC has four channel Relay & Opto coupler to demonstrate how I/O lines can be used to energise the relay and opto coupler to sense the input providing isolation.

AE-1305-LED LED Display Matrix Card
The AE-1305-LED has a matrix of 8 x 8 LED’s and is a module to demonstrate for displaying any character within the matrix. This is a small model of the display boards widely used in today’s world.

AE-1305-TWSC Thumb Wheel Switch Card
The AE-1305-TWSC has two nos. of Thumb Wheel Switches which can e read through I/O lines normally used in industrial controllers.

AE-1305-ADDA 12bit ADC Interface Card
This interface consists of 8 Channel 12 bit AD574 device with 15 microseconds conversion timer. Both unipolar & bipolar operations are possible. This module can be used where 12 bit conversion is required for better accuracy and resolution of ADC.

Microprocessor Two in one Microcontroller Training Kit

Microprocessor Two in one Microcontroller Training Kit

AE-1305-8097/80196 Kit is based on MSC-96 family Microcontrollers designed to provide ease in interaction with 16 bit micro-controller with high speed I/Q, 10 bit A/D Convertor, Pulse Width Modulated D/A output with full duplex serial pors suitale for various Industrial and Real Time Applications.

SPECIFICATIONS

  • CPU Based on 8097BH or 80C196KC/80c196KB Microcontroller Operating at 12MHz.
  • 16K bytes of RAM expandable to 32K. On board Battery Backup with 3.6v rechargeable Battery.
  • 16K bytes of EPROM expandable to 32K loaded with powerful monitor.
  • On board Assembler/Disassembler.
  • 24Parallel I/O lines using 8255 and 8 buffered lines from 8097.
  • 1 input port software programmable to be 8 bit digital input pot or 8 analog channels with 10 bit A/D Converter and sample & hold with a 24 (*U)sec.(for 12MHz Cystal) conversion time using successive approximation for conversion.
  • RTC & Watch-Dog timer & Serial port from the controller.
  • High speed I/O (HSIO) port with 8 lines. Four lines dedicated as O/P, two lines dedicated as input, and two either as I/P or O/P.
  • Two 16 bit timers (one with external clock input).
  • Cross Assembler for 80196/8097.
  • 28 Keys & 8 Seven Segment displays.
  • Facility of Uploading/Downloading files from PC.
  • EPROM Programmer for 2764/27128/27256.
  • Power Supply requirement: +5V/1.2A, +/-12V/250mA, +24V/12V/100mA.
  • User's Manual & RS232C cable.

OPTIONAL :

  • Power Supply (AE-1305-PS-III): +5V/1.2A, +/-12V/250mA & 24V/21V/100mA

ORDERING GUIDE

  • AE-1305-8097/80196 Kit & AE-1305-PS-III
  • AE-1305-8097/80196P with built in power supply

Microprocessor MSC Training Board for AE-1306-ICE31/51 Kit

Microprocessor MSC Training Board for AE-1306-ICE31/51 Kit

MSC Taining Board can be connected to AE-1305-ICE31/51 (In-Circuit Emulator cum Training Kit) through header cable.User can learn in depth about the port drivers of 8051/31 series.

SPECIFICATIONS

  • Stepper Motor: control of stepper motor in all parameters such as direction, speed and no. of steps.
  • ADC: 8 bit Analog to Digital Conversion using successive approximation technique for A to D conversion.
  • Speaker: how to generate the beep through I/O port.
  • Dot Matrix FND.
  • Working of sliding switches, Push button & LED.
  • User's Manual, Cable & Connectors.

Microprocessor 8051/8031 Microcontroller Training Kit-cum-Emulator

Microprocessor 8051/8031 Microcontroller Training Kit-cum-Emulator

AE-1305-ICE31/51 is an 8-bit Microcontroller Training Kit cum Incircuit Emulator for microcontroller family 8051/8031/8751.AE-1305-ICE31/51 comprise four components: Microcontroller Kit, In-circuit Emulator Hardware, Symbolic Debugger & Cross Assembler. These components provide the Engineer with a complete microcontroller design tool set working with microcontroller family - a cost effective package that sets a new industry standard. This kit provides 8K byte of RAM (0000 to 1FFF) with onboard battery backup for preserving data stored in this address range after power is removed for up to one year. 8K byte of EPROM (C000 to DFFF) loaded with powerful monitor program. AE-1305-ICE 31/51 is also a Stand alone In-circuit Emulator that connects to the COM port of the PC via RS232 cable provided. The 40 pin POD and flat cable are used to connect the AE-1305-ICE 31/51 to the target system. The kit has onboard feature of A/D Converter using ADC 0809 and D/A Converter using DAC 0800.

SPECIFICATIONS

  • Based on 8051/8031 microcontroller operating at 10/12 MHz clock frequency..
  • Compatible with AE-1305-P-I, AE-1305-P-II, AE-1305-P-III, AE-1305-P-IV. (Only Vinytics make microcontroller kit with emulator is compatible with AE-1305-P-IV)
  • AE-1305-ICE 31/51 comprises four components :
    • Microcontroller Kit
    • Incircuit Emulator
    • MBUG Symbolic Debugger
    • MBUG Cross Assembler
  • 8K Emulation Memory expandable upto 48K with battery backup.
  • 8K byte of EPROM loaded with powerful monitor program.
  • 48 I/O lines using 2 nos. of 8255.
  • 16 bit timer/counter using 8253.
  • 32 keys and Six Seven Segment display.
  • 8 LEDs for displaying contents of registers and two LEDs for current emulation memory.
  • 8 channel 8 bit A/D Converter using ADC 0809.
  • Single channel D/A Converter using DAC 0800.
  • 40 pin Header with cable for connecting the target system.
  • RS232 port for serial communication with IBM-PC/XT?AT.
  • Uploading & Downloading of files to/from PC.
  • Onboard assembler/disassembler.
  • Power Supply requirement : +5V/1.2A, +/-12V/250mA
  • User's Manual, Cables & Connectors.

Onboard MBUG Symbolic Debugger
MBUG is a DOS-based application program that controls and interfaces with the VMC_ICE 31/51 Incircuit Emulator through the PC Serial port. MBUG can display and modify all registers, ports, special function registers (SFRs), INTERNAL DATA, BIT, Xternal DATA and memory. The display of registers and SFRs can be customised to the programmer's requirements. On-chip user program watch variables can be designed into the register window. Two types of break-points can be set and the break-point frequency can be set up to 25 repetations. Two single-step commands are also available. The line-assembler can be used to patch already loaded programs and a disassembler is also available.

OPTIONAL:

  • Power Supply (AE-1305-PS-III): +5V/1.2A, +/-12V/250mA & 24V/21v/100mA.
  • Emulator POD for 8751/EM8751/89C51 To use AE-1305-31/51 as Emulator for 8751/89C51.
  • Emulator POD for 89C2051/89C1051 To use AE-1305-31/51 as Emulator for 89C2051/89C1051.

ORDERING GUIDE

  • AE-1305-ICE31/51 Kit & AE-1305-PS-III
  • AE-1305-ICE31/51P with built in power supply
  • Emulator PODs for 89C51.

Microprocessor 8085 - Microprocessor Kit cum In-circuit Emulator

Microprocessor 8085 - Microprocessor Kit cum In-circuit Emulator

AE-1305-ICE8085 is an 8-bit Microprocessor Training kit cum Incircuit Emulatory for 8085 Microprocessor.
Provides the Engineer, a complete microprocessor designe tool set working with 8085 - in a cost effective package that sets a new industry standard. The monitor enables AE-1305-one to use AE-1305-ICE8085 through keyboard & display having 28 keys Hexadecimal keyboard & 6 Seven Segment Display. The 28 keys consists of 16 Hexadecimal keys, 11 Functional keys & 1 Hardware Reset key.
This kit provides 48K bytes of RAM (0000 to BFFF) with onboard battery backup for preserving data stored in this address range even after power is removed.
AE-1305-ICE8085 is also a Stand Alone In-Circuit Emulator that connects to the Serial port of the PC via RS-232 cable provided with the kit.

SPECIFICATIONS

  • Based on 8085 Microprocessor operating at 6.144 MHz clock frequency
  • AE-1305-ICE8085 comprises three components:
    • Microprocessor Kit
    • In-circuit Emulator
    • Cross Assembler
  • 48K Emulation Memory, RAM area starting from0000H
  • 8K bytes of EPROM with powerful monitor program.
  • 48 I/O lines using 2 nos. of 8255.
  • Three nos. of 16 bit Timer/Counter using 8253.
  • 28 keys Hexadecimal keyboard & 6 Seven Segment display.
  • On board battery backup for Emulation memory.
  • 40 Pin Header with cable for connecting the target.
  • Programmer for 27 series EPROMs with facility to blank Check, Verify, Program & Read can be operated in Both serial & stand alone mode.
  • RS-232C port for serial communication with PC.
  • Uploading/Downloading facility to/from PC.
  • Powerful software commands like Break point, Single Stepping, Auto Single Stepping, Go, Fill, Compare, Examine Memory, Assemble etc.
  • User's Manual, cable & connectors.
  • Power Supply requirements: +5V/1.2A, +/-12V/250mA, +24V/100mA.

ON BOARD ICE8085 CROSS ASSEMBLER:

AE-1305-ICE8085 has its own fast & efficient built-in Cross Assembler that can assemble a source file and produce a modified Hex file which can be downloaded to AE-1305-ICE8085.
The 40 pin POD and flat cable are use to connect the AE-1305-ICE8085 to the taget system.The Input/Output Structure provides 48 I/O lines using 8255. It has got 16 bit programmable Timer/Counter for generation of accuate time delay under software control.

Advantage of using AE-1305-ICE8085 kit over normal 8085 Microprocessor Training kit:5V/2.5A, +/-

Ram area from 0000H location onwards, so all software & Hardware interrupts can be taught as per 8085 Instructions.

Target program development & debugging starts from 0000H location and when development is over, can be directly loaded in the EPROM.

The AE-1305-ICE8085 kit can be directly connected to the CPU of the target board to test software & Hardware by wriing small programs for enabling students/users to understand the techniques of hardware and software testing.

POWER SUPPLY - AE-1305-PS- III (OPTIONAL)

  • 5V/1.2A, +/-12V/250mA, 24V/100mA, 21V/100mA

ORDERING GUIDE

  • AE-1305-ICE8085 Kit & AE-1305-PS-III
  • AE-1305-ICE8085P with built in power supply

Microprocessor 8085 - Microprocessor Kit cum In-circuit Emulator

Microprocessor 8085 - Microprocessor Kit cum In-circuit Emulator

AE-1305-ICE8085 is an 8-bit Microprocessor Training kit cum Incircuit Emulatory for 8085 Microprocessor.
Provides the Engineer, a complete microprocessor designe tool set working with 8085 - in a cost effective package that sets a new industry standard. The monitor enables one to use AE-1305-ICE8085 through keyboard & display having 28 keys Hexadecimal keyboard & 6 Seven Segment Display. The 28 keys consists of 16 Hexadecimal keys, 11 Functional keys & 1 Hardware Reset key.
This kit provides 48K bytes of RAM (0000 to BFFF) with onboard battery backup for preserving data stored in this address range even after power is removed.
AE-1305-ICE8085 is also a Stand Alone In-Circuit Emulator that connects to the Serial port of the PC via RS-232 cable provided with the kit.

SPECIFICATIONS

  • Based on 8085 Microprocessor operating at 6.144 MHz clock frequency
  • AE-1305-ICE8085 comprises three components:
    • Microprocessor Kit
    • In-circuit Emulator
    • Cross Assembler
  • 48K Emulation Memory, RAM area starting from0000H
  • 8K bytes of EPROM with powerful monitor program.
  • 48 I/O lines using 2 nos. of 8255.
  • Three nos. of 16 bit Timer/Counter using 8253.
  • 28 keys Hexadecimal keyboard & 6 Seven Segment display.
  • On board battery backup for Emulation memory.
  • 40 Pin Header with cable for connecting the target.
  • RS-232C port for serial communication with PC.
  • Uploading/Downloading facility to/from PC.
  • Powerful software commands like Break point, Single Stepping, Auto Single Stepping, Go, Fill, Compare, Examine Memory, Assemble etc.
  • User's Manual, cable & connectors.
  • Power Supply requirements: +5V/1.2A, +/-12V/250mA, +24V/100mA.

ON BOARD ICE8085 CROSS ASSEMBLER:

AE-1305-ICE8085 has its own fast & efficient built-in Cross Assembler that can assemble a source file and produce a modified Hex file which can be downloaded to AE-1305-ICE8085.
The 40 pin POD and flat cable are use to connect the AE-1305-ICE8085 to the taget system.The Input/Output Structure provides 48 I/O lines using 8255. It has got 16 bit programmable Timer/Counter for generation of accuate time delay under software control.

Advantage of using AE-1305-ICE8085 kit over normal 8085 Microprocessor Training kit:5V/2.5A, +/-

Ram area from 0000H location onwards, so all software & Hardware interrupts can be taught as per 8085 Instructions.

Target program development & debugging starts from 0000H location and when development is over, can be directly loaded in the EPROM.

The AE-1305-ICE8085 kit can be directly connected to the CPU of the target board to test software & Hardware by wriing small programs for enabling students/users to understand the techniques of hardware and software testing.

POWER SUPPLY - AE-1305-PS- III (OPTIONAL)

  • 5V/1.2A, +/-12V/250mA, 24V/100mA, 21V/100mA

ORDERING GUIDE

  • AE-1305-ICE8085 Kit & AE-1305-PS-III
  • AE-1305-ICE8085P with built in power supply

Microprocessor 8051 Microcontroller Training Kit with LCD Display

Microprocessor 8051 Microcontroller Training Kit with LCD Display

SPECIFICATIONS

  • Based on 8051/89c52 Microcontroller.
  • On Board 32K RAM.
  • Battery backup for RAM area.
  • 64K bytes of EPROM with powerful monitor program.
  • 48 I/O lines using 2 nos. of 8255.
  • 3 channel progammable Timer/Counter using 8253.
  • Two External interrupts INT0 & INT1 from CPU.
  • IBM PC Compatible Keyboard for entering the program, editing and executing the progams.
  • 20 x 2 LCD (Liquid Crystal Display) is provided for display.
  • RS-232C interface using 8251.
  • One serial USART interface provided by 89C51/52.
  • All data, address and control signals (TTL compatible) available at FRC connector.
  • Powerful software commands like INSERT, DELETE, BLOCK MOVE, SET/CLEAR BREAK POINT, SINGLE STEP, EXAMINE/MODIFY REGISTER/MEMORY etc.
  • Provision for Microcontroller programmer for 89C51/52.
  • Power Supply requirement: +5V/1.2A, +/-12V/250mA
  • User's Manual & RS232C cable.

OPTIONAL :

  • Power Supply (AE-1305-PS-III): +5V/1.2A, +/-12V/250mA & 21V/24V/100mA
  • 8 Channel, 8 bit ADC using 0809.
  • Single channel, 8 bit DAC using 0800.
  • Real time clock
  • Programmer for 89C51/52.

ORDERING GUIDE

  • AE-1305-31/51LCD Kit & AE-1305-PS-III
  • AE-1305-31/51LCD P with built in power supply
  • Programmer for 89C51/52 on kit
  • ADC/DAC/Real time clock on kit.

Microprocessor 8051-31 Microcontroller Training Kit

Microprocessor 8051-31 Microcontroller Training Kit

SPECIFICATIONS

  • Based on 8051/8031/89c51 operating at 10/12 MHz.
  • On Board 8K RAM.
  • Battery backup for RAM area.
  • 8/16K bytes of EPROM with powerful monitor program.
  • Total memory expandable upto 128K Bytes using four 28 pin sockets.
  • 48 I/O lines using 2 nos. of 8255.
  • Two External interrupts INT0 & INT1
  • 28 keys Hexadecimal Keyboard and six Seven Segment displays.
  • RS-232C interface using 8251.
  • Auxiliary RS-232C using serial pins of 80C31.
  • All data, address and control signals (TTL compatible) available at FRC connector.
  • Powerful Software Commands like INSERT, DELETE, BLOCK MOVE, SET/CLEAR BREAK POINT, SINGLE STEP, EXAMINE/MODIFY REGISTER/MEMORY, EXECUTE etc.
  • Uploading/Downloading facility to/from PC in Intel Hex format.
  • Power Supply requirement: +5V/1.2A, +/-12V/250mA, +21V/100mA
  • User's Manual & RS232C cable..

OPTIONAL :

  • Programmer for 89C51 & 89C52 Microcontroller using 40 pin ZIF with facility to Blank Check, Verify, Program, lock & List of 89c51 Microcontroller.
  • Power Supply (PS-III): +5V/1.2A, +/-12V/250mA & 24V/100mA
  • X51 Cross Assembler for 8031/8051.

ORDERING GUIDE

  • VMC-31/51 Kit & PS-III
  • VMC-31/51P with built in power supply
  • Programmer for 89C51 Microcontroller on kit
  • X51 Cross Assembler for 8031/8051.

Microprocessor 8086 Training Kit with PC Keyboard & 14

Microprocessor 8086 Training Kit with PC Keyboard & 14

SPECIFICATIONS

  • Based on Intel's 8086/8088 CPU operating at 2.5/5 MHz.
  • 8086 Processor can be replaced by 8088 Processor.
  • Onboard sockets provided to facilitate the use of 8087 Co-processor and 8089 I/O Processor.
  • 64 K bytes of RAM available to the user using 62256.
  • 32K bytes of EPROM loaded with powerful monitor program.
  • Total on board memory capacity of 128K bytes of RAM and 128K bytes of EPROM.
  • Supports MASM (Macro Assembler).
  • Battery backup provided for RAM area.
  • 72 I/O lines through 3 nos. of 8255 available on 26 pin FRC connector.
  • 16 bit Timer/Counter through 8253.
  • RS-232C for CRT Terminal through 8251. Baud rate selection through DIP switch from 110-19,200 baud.
  • 28 keys hexadecimal keyboard and eight even segment displays.
  • Display Controller 80x25 characters.
  • 14" Monochrome Monitor (Optional).
  • 101 keys IBM PC Compatible Keyboard.
  • Two modes of Commands:
    • Hex Key pad Mode
    • Serial mode
  • Powerful software commands like GO, EXAMINE/MODIFY REGISTERS/MEMORY, SINGLE STEPPING, BLOCK MOVE, FILL, INSERT, DELETE etc.
  • Onboard Assembler & Disassembler.
  • Facility for uploading/downloading files from/to PC.
  • All address, Data and control Signals, are buffered and available at the FRC connector.
  • Power Supply requirements: +5V/1.5Amp, +/-12V/250mA, +21V/24V.
  • User's Manual.

OPTIONAL:

  • Power Supply (AE-1305-PS-IV): +5V/2.5A, +/-12V/250mA & 24V/21V/100mA
  • Interfacing Modules & Peripherals Study Cards.

Microprocessor 8085 Advance Microprocessor Trg. Kit with LCD

Microprocessor 8085 Advance Microprocessor Trg. Kit with LCD

SPECIFICATIONS

  • Based on 8085 CPU operating at 6.144 MHz. crystal.
  • 16K bytes of EPROM with powerful monitor program.
  • 8K byte of RAM available to the user.
  • Total on board memory expansion upto 64K bytes using 2732/2764/27128.
  • 20x2 Liquid Crystal Display (LCD) with backlight.
  • 48 programmable I/O lines provided through two nos. of 8255.
  • 16 bit programmable timer/counter using 8253.
  • Additional serial port using 8251
  • Printer Interface.
  • EPROM Programmer for 27 series EPROM.
  • Battery backup for user's RAM with 3.6V rechargeable cell.
  • RS-232C interface for CRT using SID/SOD lines.
  • Interrupt Controller using 8259.
  • 8 channel 8 bit ADC using 0809.
  • 1 channel 8 bit DAC using 0800.
  • 1 Opto isolated input & 1 Relay Output.
  • Real Time Clock (optional).
  • 2 Modes of Commands:
    • Key board Mode
    • Serial Mode
  • All addresses, data and control lines are buffered and made available at 50 pin FRC connector as per STD Bus configuration.
  • Powerful Software Commands like Examine/Modify memory. Examine Register, Relocate, String, Fill, Insert, Delete, Block move, Memory Compare etc.
  • On-board Single Line Assemble/Disassembler.
  • 104 keys IBM PC compatible keyboard for programing, editing, debugging, execution etc.
  • Facility for Downloading/Uploading files from/to PC.
  • Power Supply requirements: 5V/1.5A, +/-12V/250mA, +24V/21V/100mA
  • User's Manual.

POWER SUPPLY - AE-1305-PS- III (OPTIONAL)

  • 5V/1.2A, +/-12V/250mA, +24V/21V/100mA

ORDERING GUIDE

  • AE-1305-8509M Kit & AE-1305-PS-III
  • AE-1305-8509P with built in power supply

Microprocessor 8085 - Training Kit with PC Keyboard & Monitor

Microprocessor 8085 - Training Kit with PC Keyboard & Monitor

SPECIFICATIONS

  • Based on 8085 CPU operating at 6.144 MHz. crystal.
  • 8/32K bytes of RAM and space for further expansion.
  • 128KB RAM (optional).
  • 16K bytes of EPROM loaded with powerful monitor program, space for further expansion..
  • 3 nos. of 16 bit programmable timer/counter using 8253.
  • 48 I/O lines using two nos. of 8255. PPI.
  • 8 different level interrupts through 8259.
  • Six seven segment display.
  • 28 keys hexadecimal keyboard.
  • IBM PC compatible Keyboard.
  • Using 6845 CRT Controller along with character generator & Video RAM.
  • All data, address and control signals (TTL compatible) available at 50 pin FRC connector.
  • 14" Monochrome Monitor (optional).
  • EPROM Programmer for 27 series EPROMs.
  • Printer Interface.
  • Battery Backup for RAM.
  • RS-232C interface for CRT using SID/SOD lines.
  • Interrupt Controller using 8259.
  • 8 channel 8 bit ADC using 8259.
  • 1 channel 8 bit D/A using DAC 0800.
  • Real Time Clock.
  • Three modes of Commands:
    • Hex Key pad Mode
    • Serial Mode
    • CRT & ASCII Keyboard Mode.
  • On-board Single Line Assemble/Disassembler.
  • Facility for Downloading/Uploading files from/to PC.
  • Power Supply requirements: 5V/2.5A, +/-12V/250mA, +24V/21V/100mA
  • User's Manual.

POWER SUPPLY - AE-1305-PS- IV (OPTIONAL)

  • 5V/2.5A, +/-12V/250mA, +24V/21V/100mA

ORDERING GUIDE

  • AE-1305-8509M Kit & AE-1305-PS-IV
  • 14" Monochrome Monitor
  • PC Keyboard.

Microprocessor 8085 Microprocessor Training Kit with Programmer

Microprocessor 8085 Microprocessor Training Kit with Programmer

SPECIFICATIONS

  • Based on 8085 CPU operating at 6.144 MHz crystal frequency.
  • 16k bytes of EPROM loaded with powerful monitor program.
  • 8/16k byte of RAM available to the user.
  • Total on board memory expansion upto 6k bytes.
  • Six seven segment Hexadecimal display
  • Printer Interface.
  • 28 Computer graded keys: 16 hexadecimal keys and 10 for programming, editing, debugging, execution etc., 1 reset key and 1 key for vector interrupt.
  • 48 programmable I/O lines using two nos. of 8255 (PPI).
  • 3 nos. o f16 bit programmable timer/counter using 8253.
  • EPROM Programmber for 27 series EPROMs.
  • Real Time Clock Using 6242 (Optional)
  • Battery backup for RAM using 3.6V rehcargeable battery.
  • RS-232C interface for CRT using SID/SOD lines.
  • Additional serial port using 8251.
  • Interrupt Controller using 8259.
  • 8 Channel 8 bit ADC using 0809.
  • 1 Channel 8 bit DAC using DAC 0800.
  • 1 Opto isolated input & 1 Relay output.
  • 2 modes of Commands:
    • Hex Key Mode
    • Serial Mode
  • Powerful Software Commands like Examine/Modify memory, Examine register, Relocate, String, Fill, Insert, Delete, Block move, Memory compare etc.
  • Onboard Single Line Assemble/Disassembler.
  • Facility for Downloading/Uploading files from/to PC.
  • Power supply requirement: 5V/1.2A,+/-12V/250mA, +24V/21V/100mA
  • User's Manual.

POWER SUPPLY - AE-1305-PS-III (Optional)

  • +5V/1.2A,+/-12V/250mA & 24V/21V/100mA.

ORDERING GUIDE

  • AE-1305-8506 Kit & AE-1305-PS-III.
  • AE-1305-8506P with built in power supply.

Microprocessor 8085 Microprocessor Training Kit with Programmer

Microprocessor 8085 Microprocessor Training Kit with Programmer

MICROPROCESSOR TRAINER KIT WITH LED DISPLAY SPECIFICATIONS Based on 8085 CPU operating at 6.144 MHz crystal 8K bytes of EPROM loaded with powerful monitor program 8K bytes of RAM available to the user Total on board memory expansion upto 64K bytes using 2732/2764/27128/6264/ 62256 with 1 socket of 28 pin Battery back up for RAM with 3.6V rechargeable cell Memory mapping definable by the user 16 bit programmable TIMER/COUNTER using 8253 Additional serial port using 8251 (OPTIONAL) Real Time Clock (OPTIONAL) 48 I/O lines provided through 8255 RS-232C interface through SID/SOD Lines with Auto baud rate Two modes of commands: Hex Key pad & Serial mode All address, data & control lines are buffered and made available at the edge connector as per STD bus configuration 25/28 key hexadecimal keyboard and six seven segment displays through 8279 Powerful software commands like Relocate, String, Fill, Insert, Delete, Block Move, Examine/Compare Memory, Examine Register, Insert Data, Delete Data, Single Step, GO, Break Point in both Serial & Keyboard mode Facility for Downloading/Uploading files from/to PC Enclosed in an attractive ABS plastic cabinet with cover In-built Power supply User's Manual

SPECIFICATIONS

  • Based on 8085 CPU operating at 6.144 MHz crystal frequency.
  • 8/16K bytes of EPROM loaded with powerful monitor program.
  • 8/16K bytes of RAM available to the user.
  • Battery Backup for RAM with 3.6V rechargeable cell.
  • Total on board memory expansion upto 64K bytes.
  • Memory mapping definable by the user.
  • Three nos. of 16 bit programmable TIMER/COUNTER�using 8253.
  • 48 programmable I/O lines provided through two nos. of 8255.
  • RS-232C interface for CRT Terminal with auto baud rate.
  • EPROM Programmer for 27 series EPROM with facility to Program, Verify, List & Blank Check.
  • Two modes of commands: Hex Key pad mode & Serial mode
  • All address, data & control lines are buffered and made available at 50 pin FRC connector as per STD bus configuration.
  • 28 key hexadecimal keyboard and six seven segment display through 8279.
  • Powerful software commands like Relocate, String, Fill, Insert, Delete, Block Move, Examine & Compare Memory, Examine Register, Insert Data, Delete Data, Single Step, Go, Break Point in both Serial and Keyboard mode.
  • On board Single Line Assembler and Disassembler.
  • Faclity for Downloading/Uploading files from/to PC.
  • Power supply requirement: +5V/1.2A, +/-12V/250mA, +24V/21V/100mA
  • User's Manual.
  • Onboard 8 bit 8 channel ADC (Optional).
  • Onboard 8 bit 1 channel DAC (Optional).

POWER SUPPLY - AE-1305-PS-III (Optional)

  • +5V/1.2A, +/-12V/250mA, +24V/21V/100mA

ORDERING GUIDE

  • AE-1305-8503 Kit (without Programmer) & AE-1305-PS-III
  • AE-1305-8503P with built in power supply.
  • AE-1305-8503E with EPROM programmer & AE-1305-PS-III
  • AE-1305-8503EP with EPROM Programmer & built in power supply.

Microprocessor 8085 Microprocessor Training Kit

Microprocessor 8085 Microprocessor Training Kit

SPECIFICATIONS FOR AE-1305-8501

  • Based on 8085 CPU operating at 6.144 MHz crystal frequency.
  • 8/16K bytes of monitor & 8/16K bytes of RAM for user.
  • Total on board memory expansion upto 64K bytes.
  • 3 nos. of 16 bit programmable TIMER/COUNTER using 8253.
  • 24 programmable I/O lines provided through 8255.
  • RS-232C interface through SID/SOD Lines with Auto baud rate.
  • All address, data & control signal available at STD BUS.
  • 28 key hexadecimal keyboard and 6 seven segment displays.
  • On board Battery backup for RAM.
  • Power supply requirment: +5V/800mA.

ADDITIONAL SPECIFICATIONS IN AE-1305-8502

  • 22 programmable I/O lines provided through 8155.
  • Test Points for Interrupts, RD,WR & I/O/M.
  • Audio Interface (Optional).

ORDERING GUIDE

  • AE-1305-8502 kit & PS-II
  • AE-1305-8502P with built in power supply.
  • AE-1305-8501 kit & PS-II
  • AE-1305-8501P with built in power supply.

Microprocessor 8085 Training System with LCD Display

Microprocessor 8085 Training System with LCD Display

SPECIFICATIONS

  • Based on 8085, 8 bit Microprocessor.
  • Total On-board Memory capacity of 64K byrtes.
  • 8K bytes of EPROM loaded with powerful monitor program.
  • 8/32KB RAM with Battery back-up using 3.6V rechargable battery.
  • 24 I/O lines using 8255.
  • 16 bit, 3 channel Timer/Counter using 8253.
  • Display : 16x1 LCD.
  • Keyboard : IBM PC Compatible ASCII Keyboard.
  • RS.232C interface through SID/SOD lines with auto baud rate.
  • Facility to Upload/Download programs to/from PC.
  • On board Assembler/Disassembler.
  • In-built power supply.
  • All data, address & control signals are available at 50 pin FRC connector as per STD cus configuration.

OPTIONAL

  • Power Supply AE-1305-PS-II : +5V/1A, +/-12V/200mA.
  • Power Supply AE-1305-PS-III : +5V/1.2A, +/-12V/250mA, 21V/24V/100mA.
  • X8085 Cross Assembler for 8085.
  • Hardware Manual gives details about 8085 & other Peripherals/Memory Chips.
  • Laboratory Manual gives Doftware experiments as well as Hardware experiments to be performed with interfacing Modules and experiments with various peripheral chips like 8253, 8279 and 8251.
  • Interfacing Modules & Peripherals Study Cards. Mini projects to interface with I/O lines and study cards to understand the working of peripheral IC's.

Microprocessor 8085 Training System with LCD Display

Microprocessor 8085 Training System with LCD Display

SPECIFICATIONS

  • Based on 8085, 8 bit Microprocessor.
  • Total On-board Memory capacity of 64K byrtes.
  • 8K bytes of EPROM loaded with powerful monitor program.
  • 8/32KB RAM with Battery back-up using 3.6V rechargable battery.
  • 24 I/O lines using 8255.
  • 16 bit, 3 channel Timer/Counter using 8253.
  • Display : 16x1 LCD.
  • Keyboard : 28 Keys Hex Keyboard.
  • RS.232C interface through SID/SOD lines with auto baud rate.
  • Facility to Upload/Download programs to/from PC.
  • In-built power supply.
  • All data, address & control signals are available at 50 pin FRC connector as per STD cus configuration.

OPTIONAL

  • Power Supply AE-1305-PS-II :+5V/1A, +/-12V/200mA.
  • Power Supply AE-1305-PS-III : +5V/1.2A, +/-12V/250mA, 21V/24V/100mA.
  • X8085 Cross Assembler for 8085.
  • Hardware Manual gives details about 8085 & other Peripherals/Memory Chips.
  • Laboratory Manual gives Doftware experiments as well as Hardware experiments to be performed with interfacing Modules and experiments with various peripheral chips like 8253, 8279 and 8251.
  • Interfacing Modules & Peripherals Study Cards. Mini projects to interface with I/O lines and study cards to understand the working of peripheral IC's.